Kicker Hideaway Mounting Screw Size: Know Before You Install (2024)

The Kicker Hideaway subwoofer is a compact powered subwoofer designed to deliver surprising low-frequency output from a small enclosure. It combines a 150-watt amplifier and an 8-inch subwoofer to add bass to any vehicle. The unit comes with a mounting kit that includes screws and straps. The installation process may vary depending on the vehicle's make and model, but it generally involves connecting the power, signal, and remote turn-on wires, as well as running the speaker wires to the desired location.

Kicker Hideaway HS8 subwoofer installation in a Jeep Wrangler

The Kicker Hideaway HS8 subwoofer can be installed in a Jeep Wrangler in a few hours, though it may take longer if you're figuring things out as you go. The process involves placing the subwoofer under the right rear passenger seat and running wires to the battery and speakers. Here is a step-by-step guide on how to install the Kicker Hideaway HS8 subwoofer in a Jeep Wrangler:

Step 1: Place the Kicker Hideaway under the Right Rear Passenger Seat

Place the Kicker Hideaway subwoofer under the right rear passenger seat. This location provides easy access to the necessary wiring connections.

Step 2: Run the Red Wire to the Battery

Use a pry tool to lift the right seam of the floor and push along until you reach the A-pillar. Run the red wire up the pillar between the plastic moulding and the frame of the car. Remove the small panel where the door latch is located to assist in running the wire up the pillar. Use a hanger to guide the wire down the seam of the engine compartment and connect it to the positive terminal of the battery.

Step 3: Connect the Speaker Wires

Connect the speaker wires from the Kicker terminal to the Soundbar left and right speaker wires by accessing the Right B-pillar door latch. Use Velcro to secure and organise the wires. The Hideaway speaker wires are colour-coded as follows:

• White is Left +
• White/Black is Left –
• Grey is Right +
• Grey/Black is Right –
• Gray/light green is Left +
• Gray/dark green is Left –
• Dark green/light green is Right +
• Dark green/gray is Right –

Step 4: Connect the Black Ground Wire

Pull up on the passenger plastic moulding, lift the carpet, and reveal the screw underneath. Connect the black ground wire using the supplied screw point. Tuck in any excess wires before running the quick connect to the Hideaway connection point.

Step 5: Run the Blue Remote Wire to the 12V Cigarette Lighter

Run the blue remote wire the same way you ran the red wire, but instead of connecting it to the battery, run it to the 12V cigarette lighter in the front panel. This is important because if you don't connect the remote wire, the amplifier will always stay on and drain your battery.

Step 6: Adjust the Kicker Settings

Plug in the Kicker quick-access connector, start your Jeep, and adjust the settings to your preference. Turn off your Jeep to make sure the amplifier turns off as well. Enjoy your enhanced music experience!

Tools and Materials:

• Screwdriver
• Wire cutters/stripper
• Electrical tape
• Pry tool
• 1/4 inch drive ratchet
• Socket
• Hanger
• Velcro
• Scissors
• Razor blade

Kicker Hideaway mounting options in a Ford F150

There are several mounting options for the Kicker Hideaway in a Ford F150. One popular option is to place it behind the rear seat, either on the left or centre. To secure it in place, some people have used MDF or a 2x4 piece of wood, attached to the two seatbelt bolts with new nuts. Others have used the included Velcro straps to fasten it to the rear insulation panel, cutting two slits in the panel for the straps. Another option is to use the supplied screws and washers to attach the included straps to the floor of the cab.

In terms of wiring, the Kicker Hideaway can be connected to the OEM connector in the truck using a Motorcraft WPT1212 Connector Harness. This allows for a plug-and-play installation without any cutting of factory wires. The Kicker harness has left and right speaker connections, which need to be wired to the correct WPT1212 harness wires.

To enable the subwoofer, you will need to use Forscan to set the ACM to "auxiliary subwoofer" and "Supercab 7 speaker with Kicker audio".

Kicker Hideaway/amp board mounting to the back cabin wall of a Ford Maverick

The Kicker Hideaway/amp board can be mounted to the back cabin wall of a Ford Maverick. The Maverick's cabin space is about 100.3 cubic feet, with a length of 199.7 inches, a height of 68.7 inches, and a width of 72.6 inches. The Maverick's rear cabin wall has flaps for pressure relief when closing doors and air exit when the HVAC is on fresh air.

When mounting the Kicker Hideaway/amp board, it is important to consider the thickness of the cabin wall and choose appropriate mounting screws. The specific screw size will depend on the thickness of the wall and the weight of the Kicker Hideaway/amp board. It is recommended to use screws that are long enough to securely attach the board to the wall, but not so long that they protrude through the other side. Standard wood screws or self-tapping screws may be suitable, depending on the material of the cabin wall.

One method for mounting the Kicker Hideaway/amp board is to use elevator bolts and JB Weld. This method involves gluing the bolts to the wall and then attaching the board to the bolts. Another method is to use MDF and secure it to the two seatbelt bolts with angle aluminium and new nuts. Alternatively, you can cut slits in the rear insulation panel and use the included velcro straps to fasten the board.

When installing the Kicker Hideaway/amp board, it is important to follow the instructions provided by the manufacturer and to take appropriate safety precautions when working with tools and equipment.

Kicker Hideaway HS8 subwoofer specifications

The Kicker Hideaway HS8 is a compact powered subwoofer designed for use in vehicles. It combines a powerful 150-watt amplifier with an 8-inch subwoofer, delivering surprising low-frequency output from a small enclosure.

Specifications

• Dimensions: 9.45" x 13.78" x 3.15" (23.8 cm x 35.2 cm x 7.94 cm)
• Weight: 9.4 lbs (4.3 kg)
• Subwoofer Size: 8 inches (20 cm)
• RMS Power: 150 watts
• Frequency Response: 25-120 Hz
• Crossover: 12dB/octave low pass at 50-120Hz; 24dB/octave high pass at 25Hz
• Phase Switch: 0°/180°
• Input Sensitivity: Low level – 125mV-5V; High level – 250mV-10V
• KickEQ Boost: Variable to +6dB @ 40Hz
• Remote Bass: Included

Installation

The Kicker Hideaway HS8 is designed for easy installation and removal. It comes with a quick-connect power plug, nylon straps with Velcro fasteners, and a remote bass control knob for fine-tuning bass levels. The installation process typically involves connecting the power, signal, and remote turn-on wires, as well as securing the subwoofer in place using the provided straps and fasteners.

Performance

The Kicker Hideaway HS8 delivers impressive bass performance for its size. It provides thumping bass and clear sound, enhancing the audio experience in a vehicle without taking up too much space. The remote bass control allows for convenient adjustment of bass levels to suit different music preferences.

Comparison with Other Models

The Kicker Hideaway HS8 is a more compact model compared to its bigger brother, the HS10, which is a 10-inch subwoofer. The HS8 is designed to fit in tighter spaces while still delivering the renowned Kicker bass performance.

Kicker Hideaway subwoofer wiring and installation in a Honda Accord

The Kicker Hideaway subwoofer is an amplifier/subwoofer combo that can be installed in your car to improve the bass of your audio system. The following guide will take you through the process of wiring and installing the Kicker Hideaway subwoofer in a Honda Accord.

Tools Required:

• Screwdriver
• Wire cutters/stripper
• Electrical tape
• Pry tool
• 1/4 inch drive ratchet
• Socket
• Hanger
• Velcro
• Scissors
• Razor blade

Wiring and Installation:

• Place the Kicker Hideaway under the right rear passenger seat.
• Run the packaged quick-connect plug red wire along the right seam of the floor. Use a pry tool to lift and push the wire along the seam until you reach the A-pillar.
• Run the red wire up the pillar, between the plastic moulding and the frame of the car. Remove the small panel where the door latch is located to assist in running the wire.
• Run the wire down the seam of the engine compartment and connect it to the positive terminal of the battery.
• Connect the speaker wires from the Kicker terminal to the Soundbar left and right speaker wires by accessing the Right B-pillar door latch. Connect all speaker wires and use Velcro to ensure wire discipline.
• Connect the black ground wire by using a supplied screw point underneath the carpet. Pull up on the passenger plastic moulding, lift the carpet, and reveal the screw. Tuck in any excess wires here.
• Run the blue remote wire the same way you ran the red wire, but instead, connect it to the 12V cigarette lighter in the front panel. This is important to ensure the amplifier turns off when the car is turned off, otherwise, it will drain your battery.
• Make the necessary adjustments to the Kicker auto turn-on, input level, phase, base boost, and gain settings as per your preferences.

Tips:

• You do not need a line out converter (LOC) for this installation.
• Secure your Hideaway using the supplied Velcro.
• The Kicker Hideaway can be purchased from Best Buy or online retailers such as eBay and Amazon.

Please note that this guide is based on a general installation process and may require some adjustments specific to your Honda Accord model and year.

Frequently asked questions